Electrostatic manual powder coating set with long spray nozzles
Electrostatic manual powder coating set with long spray nozzles
Electrostatic manual powder coating set with long spray nozzles
Electrostatic manual powder coating set with long spray nozzles
Price
US $875
Model
CL-668
MOQ
1 piece

Item specifics

Condition
New
Type
Manual powder coating equipment
Substrate
Steel
Coating
Powder Coating
Voltage
100-240V
Power(W)
50W
Weight
55KGS
Certification
CE
Warranty
1 YEAR

Review

Description

Electrostatic manual powder coating set with long spray nozzles

  1. Quick and simple color change
  2. Enhanced coating quality of flat and complex parts
    • Reduced operator fatigue
    • Effective coating in corners and recesses
    • Improved recoating ability





Application

The powder spray equipment is built exclusively for electrostatic coating with organic powders.

The electrostatic powder manual coating equipment with the COLO-06 manual powder gun is ideally suited

for manual coating of objects in small series.


Spare parts of COLO-06 manual powder gun-Compatible with GM03



colo-06.jpg


Spare parts of the spraying painting machine CL-668-Powder injector 1007 780, compatible

with GM03 manual gun

2012.10.1


Special features of the painting machine
1

NEW ACCURATE DESIGN

2

SUPERIOR PERFORMANCE

3

OPTIMUM COATING RESULTS

 


4

POWDER IS MORE STABLE

5

MORE UNIFORM

6

BETTER ATOMIZATION

7

Up to 20 coating programs can be stored in the control unit


Technical Data

Electrical data

  1. Power range                                  220V/110V
  2. Frequency                                     50HZ /60HZ
  3. Temperature range in use                      -10 ℃+50 ℃

Powder Gun

  1. Gun weight:    ………………                    500G
  2. Rated output voltage ………                      24VDC
  3. Input voltage     ……………                       - 200kv
  4. Maximum output current  ………                   180Ua(max)
  5. Maximum output voltage…………                   0-100KV (  adjustable)   
  6. Maximum powder injection :………                    600g/min
  7. Polarity ………………                                negative (-)  

Pneumatic data

  1. Maximum input-air pressure …………..                 10kg/cm
  2. Optimum input-air pressure……..                        6kg/cm
  3. Minimum input-air pressure   ……                      4kg/cm
  4. Maximum water vapor content or compressed air …..      1.4g/N m3
  5. Maximum oil vapor content of compressed air   ……..     0.1ppm
  6. Maximum compressed-air consumption………            13.2 m3/h

-INSTALLATION

Propery ground all equipment in the spray area to an earth ground and maintain this ground

Remove all containers of volatiles from the spray area

Establish and maintain a grounded area for the spray operator

The gun of xseries must be connect to xcontrol unit

OPERATION

The operator should hold the gun in his bare hand

If gloves are worm ,the palm should be out to assure skin to metal contact

The operator should wear shoes with conductive shoes e.g leather

     Rubber shoes are not conductive .

Ground the tip of the gun before cleaning or changing nozzles.

When the gun is not in use , it should be hung so that the nozzle is within four inches of a grounded conductor

The operator should wear a filter-type respiator anytime he is exposed to dusty conditions

High pressure powder many cause injury ,Keep the rear switch  off position in no –use condiction

  MAINTENANCE

Make a periodic confirmation of grounding to earh of all equipment in the spray area .

Exercise good housekeeping practices , do not allow dirt or powder to accumulate on the feeder /powder unit , cable or gun.

Keep the cabinet door


Powder coating

Powder coating is a type of coating that is applied as a free-flowing, dry powder. The main difference between a conventional liquid

paint and a powder coating is that the powder coating does not require a solvent to keep the binder and filler parts in a liquid

suspension form. The coating is typically applied electrostatically and is then cured under heat to allow it to flow and form a "skin". The

powder may be a thermoplastic or a thermoset polymer. It is usually used to create a hard finish that is tougher than conventional

paint. Powder coating is mainly used for coating of metals, such as "whiteware," aluminium extrusions, and automobile and bicycle

parts. Newer technologies allow other materials, such as MDF (medium-density fibreboard), to be powder coated using different

methods.

The process of the coating

The process of the coating is like this :the powder is fluidized in the powder hopper. The injectors transport the powder through the hoses to the guns . The guns spray a powder/air mixture onto the workpieces.

The powder coating process involves three basic steps:

Part preparation or the pre-treatment

The powder application

Curing



Customers visting

Colo has exported to more than 90 countries, such as Mexico, Colombia, Peru, Canada, the United States, Brazil,

Russia, Poland, France, Germany, Italy,Egypt, Vietnam, India, Saudi Arabia, South Africa and other countries.


We have built good long-term relationship with our customers. They come to visit our factory from time to time.

visit.png


Company Information

Colo is the leading powder coating equipment manufacturer in China, which provides high quality equipments

to more than 90 countries all oven the world with advanced manufacturing machines and professional

technicians. Colo offers a wide range of power coating equipments, namely powder coating machine, power

coating gun, spray booth, curing oven, automatic powder coating applicator, powder coating line and

replacement of spare parts for the famous brand in the world.

Welcome guests from all countries in the world to visit our factory.

1-.jpg+.jpg

COLO Powder Coating Systems is a top supplier of powder coating systems and powder coating equipment including automated equipment, spray booths and spare parts famous brand in china.